CCNA Chapter…7

Lab 7.2.5 Configuring a Wireless Access Point

Step 1: Verify connectivity between the computer and the multi-function device

d. Write down the command used to ping the multi-function device……..(ping 192.168.1.1)

Step 2: Log in to the multi-function device and configure the wireless network

e. Write down the exact SSID name that you are using……….(informatika08)

f. Click on the Radio Band drop-down menu and write down the two options…………….(Auto dan manual)

Step 3: Reflection

a. How many wireless networks do you think could be configured in one classroom? What would limit this?…………….(1-50)

b. What do you see as a potential security problem when you broadcast your SSID from the AP?…………….(Seorang administrator jaringan sering menggunakan SSID publik, yang ditetapkan pada titik akses dan disiarkan ke semua perangkat nirkabel dalam jangkauan, sehingga hal ini dapat mempermudah resiko di hack oleh pihak tak bertanggung jawab)

Lab 7.2.6 Configuring a Wireless Client

b. Who is the manufacturer of the wireless NIC?………(IEEE)

c. Describe how you installed the wireless NIC driver………

Step 2: Install the wireless NIC

a. When prompted, connect the USB NIC cable to an available USB port. Click Next to continue.

Step 3: Attach to the wireless network

b. Which SSID are you using?…………..(super scan)

d. What is the signal strength for the wireless NIC?…………….(antena konektor)

e. Did the wireless NIC see any other wireless networks in the area?……….(ya)

g. What is another name for a wireless host?…………(network adapter)

h. Is it better to use the client software from the wireless NIC manufacturer or let Windows XP control the wireless NIC?………..(let Windows XP control the wireless NIC)

Step 4: Determine the NIC driver version

b. To check the driver version for the NIC you installed, click Start, select Control Panel and then Network Connections. Right-click on the wireless connection and select Properties. Click the Configure button for the NIC and then the Driver tab. What is the name and version of the driver you installed?……….(PCMCIA, Personal Computer Memory Card International Association)

Step 5: Determine if the NIC driver is the most current

a. Search the NIC manufacturer web site for drivers that support the wireless NIC you installed. Are there more current ones available?………(PCMCIA saat ini masih tersedia)

b. What is the most current one listed?……..(Wireless Ethernet)

c. If there is a more current driver, how would you apply it?

Step 6: Verify connectivity

e. If you receive the Linksys Setup screen, you have established connectivity with the AP. If you do not establish connectivity, you will have to troubleshoot the connection by checking to ensure the devices are turned on and the IP addresses on all devices are correct. Which IP address should be configured on the wireless NIC?

Step 7: Reflection

a. Do you think the process of setting up a wireless network at a food store or book store is any different from what you just did?……….(ya)

b. Do you think the AP model that you are using would be sufficient for the food store in your neighborhood? Why or why not?

Lab 7.3.5 Configuring Wireless Security

Step 1: Plan the security for your home network

a. List at least six security best practices that you should implement to secure your multi-function device
and wireless network.

1) Kurangi kekuatan pancar antena WAP

2) Berikan security code

3) Aktifkan MAC address filter.

4) Ganti Password default

5) Disable Broadcast SSID

6) Disable DHCP Server

 

b. Describe what the security risk is for each item.

1) kelemahan atau resikonya misalnya disebuah tempat usaha atau perusahaan maka semakin jauh titik akses dari akses point mengakibatkan kecepatan akses sangat terpengaruh atau bahkan tidak menjanjikan sama sekali.

2) bagi orang yang tidak paham teknologi akan kebingungan dalam memberikan security code.

3) jika seandainya MAC address seseorang client pernah diblokir pada suatu tempat, akan tetapi belum dibuka kembali maka tidak bisa digunakan pada tempat akses lain.

4) jika password pada default diganti, akan susah mengetahui paswor yang baru jika tidak dikonfirmasikan terhadap teknisi.

5) jika tidak diaktifkan kembali, maka titik access tidak dapat diditeksi oleh wireless adapter.

6)jika di disabledkan maka hanya IP address yang telah diregisterkan yang bisa mengakses jaringan, sehingga jaringan tidak bersifat bebas layaknya wi-fi zone pada umumnya.

Step 2: Connect a computer to the multi-function device and log in to the web-based utility

a. Connect your computer (Ethernet NIC) to the multi-function device (port 1 on the Linksys WRT300N)
by using a straight-through cable.
b. The default IP address of the Linksys WRT300N is 192.168.1.1, and the default subnet mask is
255.255.255.0. The computer and Linksys device must be on the same network to communicate with
each other. Change the IP address of the computer to 192.168.1.2, and verify that the subnet mask is
255.255.255.0. Enter the internal address of the Linksys device (192.168.1.1) as the default gateway.
Do this by clicking, Start > Control Panel > Network Connections. Right click on the wireless
connection and choose Properties. Select the Internet Protocol (TCP/IP) and enter the addresses as
shown below.

c. Open a web browser, such as Internet Explorer, Netscape, or Firefox and enter the default IP address
of the Linksys device (192.168.1.1) into the address field and press Enter.

d. A screen appears, requesting your user name and password.

b. Leave the User name field blank and enter admin for the password. It is the default password on the
Linksys device. Click OK. Remember that passwords are case-sensitive.
c. As you make the necessary changes on the Linksys device, click Save Settings on each screen to
save the changes or click Cancel Changes to keep the default settings

Step 4: Change the Linksys device password

a. The initial screen displayed is the Setup > Basic Setup screen.

b. Click the Administration tab. The Management tab is selected by default.

c. Type in a new password for the Linksys device, and then confirm the password. The new password
must not be more than 32 characters and must not include any spaces. The password is required to
access the Linksys device web-based utility and Setup Wizard.

d. The Web Utility Access via Wireless option is enabled by default. You may want to disable this feature to further increase security.

e. Click the Save Settings button to save the information.
NOTE: If you forget your password, you can reset the Linksys device to the factory defaults by pressing the RESET button for 5 seconds and then releasing it. The default password is admin.

Step 5: Configure the wireless security settings

a. Click the Wireless tab. The Basic Wireless Settings tab is selected by default. The Network Name
is the SSID shared among all devices on your network. It must be identical for all devices in the
wireless network. It is case-sensitive and must not be more than 32 characters.

b. Change the SSID from the default of linksys to a unique name. Record the name you have chosen………(informatika)

c. Leave the Radio Band set to Auto. This allows your network to use all 802.11n, g, and b devices.

d. For SSID Broadcast, select the Disabled button to disable the SSID broadcast. Wireless clients
survey the area for networks to associate with and will detect the SSID broadcast sent by the Linksys
device. For added security, do not broadcast the SSID.

e. Save your settings before going to the next screen.

Step 6: Configure encryption and authentication

a. Choose the Wireless Security tab on the Wireless screen.

b. This router supports four types of security mode settings:
• WEP (Wired Equivalent Privacy)
• WPA (Wi-Fi Protected Access) Personal, which uses a pre-shared key (PSK)
• WPA Enterprise, which uses Remote Access Dial In User Service (RADIUS)
• RADIUS

c. Select WPA Personal Security Mode.

d. On the next screen, choose an Encryption algorithm.
To secure a network, use the highest level of encryption possible within the Selected Security mode.
The following Security Modes and Encryption levels are listed from least secure (WEP) to most
secure (WPA2 with AES)
• WEP
• WPA
o TKIP (Temporal Key Integrity Protocol)
o AES (Advanced Encryption System)
• WPA2
o TKIP
o AES
AES is only supported by newer devices that contain a co-processor. To ensure compatibility with all
devices, select TKIP.

e. For authentication, enter a pre-shared key between 8 and 63 characters. This key is shared by the
Linksys device and all connected devices.

f. Choose a key renewal period between 600 and 7200 seconds. The renewal period is how often the
Linksys device changes the encryption key.

g. Save your settings before exiting the screen.

Step 7: Configure MAC address filtering

a. Choose the Wireless MAC Filter tab on the Wireless screen.

b. MAC address filtering allows only selected wireless client MAC addresses to have access to your
network. Select the radio button to Permit PCs listed below to access the wireless network. Click
the Wireless Client List button to display a list of all wireless client computers on your network.

c. The next screen allows you to identify which MAC addresses can have access to the wireless
network. Click the Save to MAC Address Filter List check box for any client device you want to add,
and then click the Add button. Any wireless clients, other than those in the list will be prevented from
accessing your wireless network. Save your settings before exiting the screen.

Step 8: Reflection

a. Which feature that you configured on the Linksys WRT300N makes you feel the most secure and
why?……………( aplikasi atau program yang membuat saya merasa lebih aman dan nyaman ketika mengkonfigurasi ialah MAC address filtering. Alasannya karena pada aplikasi ini terdapat sebuah pilihan untuk memberikan izin access kepada client yang telah terlebih dahulu alamat IP dan MAC address nya dicantumkan atau didaftarkan.)

b. Make a list of other items that could be done to make your network even more secure.

(Pada pengaturan wireless kita pilih wireless security dan security modenya kita ganti dari disabled menjadi WEP sehingga dapat memberikan kunci berlapis. Atau pada system operasi windows biasa kita aktifkn juga menu firewall dan kita aktifkan juga menu SYS).



Tinggalkan Balasan

Isikan data di bawah atau klik salah satu ikon untuk log in:

Logo WordPress.com

You are commenting using your WordPress.com account. Logout / Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout / Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout / Ubah )

Foto Google+

You are commenting using your Google+ account. Logout / Ubah )

Connecting to %s